Intel MPCMM0001 Manual do Utilizador Página 83
- Página / 281
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
MPCMM0001 Chassis Management Module Software Technical Product Specification 83
The Command Line Interface (CLI)
powerstate
Retrieves and sets power
state of a blade.
Get: This is used to find out
the powered on/off or offline
state of a blade
Set: To reboot, shutdown and
turn on a blade
If “reset” is used on CMM
location, the software will
check for redundancy and a
reset will only occur if a
redundant partner is
identified.
“PowerOff” is not supported
on the CMM location.
Both
"<location>: <currentState> (Mx)"
where Mx is the ATCA-defined M state of
the location
"Reset"
"PowerOff"
"PowerOn"
presence
Used to find out if a particular
location is occupied or
present in the chassis. This
can be blades or intelligent
entities like fan trays or
PEMs.
Get
"<location> is <presenceState>."
Where <presenceState> is
"present" - if the location is present
"not present" - if the location is not
present or the CMM can not
communicate with it.
N/A
presentpowerlevel
Get/Set the current power
level of a FRU.
Get
"The FRU Power Level is <PwrLevel>
Consuming <WattageValue> Watts"
where
<PwrLevel> is the current power level of
the FRU in the range 1-20
<WattageValue> is the current power
draw in watts
N/A
sel
Returns the System Event
Log of the specified location.
Get
Listing of the interpreted SEL log of the
location. The listing is of the format:
“<Entry1>\n\n<Entry2>…”
where <EntryM> is of the format:
<Timestamp in Linux date
format>\n\t<SensorName>\t<EventDescr
iption>
N/A
grantedboardekeys
Get the EKeys that have
been granted to the Board.
Get
Base Interface Ekeys:
<EkeyList>
Fabric Interface EKeys:
<EkeyList>
Update Channel Interface EKeys:
<EkeyList>"
where <EkeyList> is a list of ekey
settings for the interface such as
Ekey1 : enabled
EKey2 : disbaled
EKey3 : no set
N/A
Table 25. Dataitem Keywords for All Locations Except Chassis and System (Sheet 3 of 4)
Dataitem Description Get/Set CLI Get Output Valid Set Values
- NetStructure™ 1
- MPCMM0001 Chassis 1
- Management Module 1
- Contents 3
- Revision History 15
- Introduction 1 16
- Introduction 17
- Software Specifications 2 18
- 2.8.3 Clearing the SEL 20
- 2.8.4 Retrieving the Raw SEL 20
- Failover 3 21
- 3.3.1 SDR/SIF Synchronization 23
- 3.5 Datasync Status Sensor 25
- 3.5.1 Sensor bitmap 25
- 3.5.2 Event IDs 25
- 3.5.4 SEL Event 27
- 3.5.5 SNMP Trap 27
- 3.5.6 System Health 28
- 3.6 CMM Failover 28
- 3.6.3 Manual Failover 29
- 3.7 CMM Ready Event 30
- Built-In Self Test (BIST) 4 31
- 4.2 Boot-BIST 33
- 4.3 Early-BIST 33
- 4.4 Mid-BIST 33
- 4.5 Late-BIST 33
- 4.6 QuickBoot Feature 34
- 4.6.1 Configuring QuickBoot 34
- 4.9 BIST Test Descriptions 36
- 4.9.4 FPGA Version Check 37
- 4.9.7 OS Image Checksum Test 37
- 4.9.8 CRC32 Checksum 37
- Built-In Self Test (BIST) 38
- Re-enumeration 5 39
- 5.3 Re-enumeration of M5 FRU 40
- 5.4 Resolution of EKeys 40
- 5.5 Events Regeneration 40
- 6.1 Overview 41
- 6.2 Processes Monitored 42
- 6.4.1 Examples 43
- 6.5 SNMP MIB Commands 44
- 6.7.1 No Action Recovery 45
- Critical 52
- 6.9 Configuring pms.ini 55
- 6.9.1 Global Data 55
- 6.9.2 Process Specific Data 56
- 6.9.2.6 Administrative State 57
- 6.9.2.9 Process Ramp-up Time 57
- ProcessSeverity = 1 58
- RecoveryAction = 1 58
- 6.9.3.2 Monitor Process 59
- 6.9.3.4 CMM Wrapper Process 60
- 6.9.3.5 SNMP 61
- 6.9.3.6 CLI Server 61
- 6.9.3.7 Command Handler 61
- 6.9.3.8 BPM 62
- 6.9.3.10 Inet Daemon 63
- 6.10.1 PIE Section Name 64
- 6.10.3 Unique ID 65
- 6.10.4 Administrative State 65
- 6.10.6 Chassis Applicability 66
- 6.11 WP/BPM PIE 67
- 7.1 Hot Swap States 68
- 7.2 FRU Insertion 68
- 7.3 Graceful FRU Extraction 68
- 7.7 Power Feed Targets 69
- 7.8 Pinging IPMI Controllers 70
- 8.1 CLI Overview 71
- 8.2 Connecting to the CLI 71
- /etc/rc.d/network reload 73
- 8.3.1.3 Setting eth0 to DHCP 74
- 8.3.1.4 Setting eth1 to DHCP 74
- 8.3.2 Setting a Hostname 75
- 8.3.5 Telnet into the CMM 76
- 8.3.7 FTP into the CMM 76
- 8.3.8 Rebooting the CMM 76
- 8.4.2 Help Parameter: -h 77
- 8.4.3 Location Parameter: -l 77
- 8.4.4 Target Parameter: -t 78
- Table 22. CMM Targets 79
- 8.4.5 Dataitem Parameter: -d 80
- 8.4.5.2 Target Dataitem Lists 93
- 8.4.6 Value Parameter: -v 97
- 8.4.7 Sample CLI Operations 97
- Resetting the Password 9 99
- Sensor Types 10 101
- 10.4 Discrete Sensors 102
- 10.4.1 Discrete Sensor Events 103
- Health Events 11 104
- 11.1.3 SEL Sensor Types 105
- 11.1.4 SNMP Trap Event Syntax 105
- 11.2 Sensor Targets 106
- 11.3 Healthevents Queries 107
- 11.3.3 No Active Events 108
- 11.4.1 All Locations 109
- Health Events 110
- 11.4.2 CMM Location 115
- 11.4.3 Chassis Location 120
- Front Panel LEDs 12 123
- 12.1.2 Health LED 124
- 12.1.3 Hot Swap LED 124
- 12.1.4 User Definable LEDs 124
- 12.6 LED Boot Sequence 126
- Node Power Control 13 127
- 13.3.3 Resetting a Board 128
- Electronic Keying Manager 14 129
- CDMs and FRU Information 15 130
- 15.4 FRU Query Syntax 131
- Fan Control and Monitoring 16 132
- 16.5 CMM Cooling Table 133
- 16.6.1 CMM Control Mode 134
- 16.6.2 Fantray Control Mode 134
- 16.6.5 Automatic Mode Change 135
- 16.8 Fantray Properties 136
- 16.10 Fantray Insertion 136
- 16.11 Default Cooling Values 137
- 16.11.1 Vendor Defaults 137
- 16.11.3 Code Defaults 138
- 16.11.4 Restoring Defaults 138
- 16.13 Chassis vs. Fantray 139
- 17.1 CMM MIB 141
- 17.2 MIB Design 141
- 17.2.1 MIB Tree 141
- CMM Custom MIB Tree 142
- 6].52.1) (Sheet 1 of 2) 156
- 6].52.1) (Sheet 2 of 2) 157
- 17.3 SNMP Agent 158
- 17.4 SNMP Trap Utility 160
- 17.5.3 Alerts Using SNMP v3 161
- 17.5.4 Alert Using UDP Alert 161
- 17.6 SNMP Security 162
- 17.6.1 SNMP v1 Security 162
- Protocol 162
- 17.7 SNMP Trap Descriptions 162
- 17.8 Snmpd.conf File 163
- CMM Scripting 18 164
- 18.3.1 Event Codes 165
- 18.4.1 Sensor Data Bits 166
- The current value is 0xNNNN 167
- CMM is [Active/Standby] 167
- CMM enumeration is completed 167
- 18.4.3 CMMReadyTimeout Value 168
- 18.5 FRU Control Script 169
- 18.5.1 Command line arguments 170
- 18.5.2 Sample frucontrol file 170
- CMM Scripting 171
- 19.2 Using the RPC Interface 174
- 19.2.1 GetAuthCapability() 175
- 19.2.2 ChassisManagementApi() 175
- Remote Procedure Calls (RPC) 177
- 19.3 RPC Sample Code 187
- 19.4 RPC Usage Examples 187
- 20.1 RMCP References 190
- 20.2 RMCP Modes 190
- 20.4 RMCP Discovery 191
- 20.5 RMCP Session Activation 191
- 20.6 RMCP Port Numbers 192
- 20.7 IPMB Slave Addresses 193
- 20.8 CMM RMCP Configuration 193
- CB Not Found 198
- Command and Error Logging 21 199
- 21.3 Cmmdump Utility 200
- Application Hosting 22 201
- 22.3.2 RAM Constraints 202
- 22.3.3 Interrupt Constraints 203
- Updating CMM Software 23 204
- 23.4 Update Package 205
- 23.4.3 Component Versioning 207
- 23.6 Update Mode 208
- 23.7 Update_Metadata File 209
- 23.10 Single CMM System 210
- 23.11 Redundant CMM Systems 210
- 23.13 Hooks for User Scripts 211
- #!/bin/bash 212
- 23.14 Update Process 213
- 23.17 Redboot* Update Process 215
- 23.17.1 Required Setup 215
- 23.17.2 Update Procedure 215
- Updating Shelf Components 24 217
- IPMI Pass-Through 25 218
- 25.2.2 Response String 219
- 25.2.3 Usage Examples 219
- 25.3 SNMP 219
- 25.3.1 Usage Example 219
- IPMI Pass-Through 220
- FRU Update Utility 26 221
- 26.3 FRU Update Process 222
- 26.4 FRU Recovery Process 222
- 26.5 FRU Verification 223
- 26.6 FRU Display 223
- 26.10 Updating the FRU 225
- 26.11 Getting the Inventory 225
- 27.2 File Format 227
- 27.3 String Constraints 227
- 27.4 Numeric Constraints 228
- 27.5 Tags 228
- 27.6 Control Commands 228
- 27.6.1 IFSET 228
- 27.6.2 ELSE 229
- 27.6.3 ENDIF 229
- 27.6.4 SET 229
- 27.6.5 CLEAR 230
- 27.6.6 CFGNAME 230
- 27.6.7 ERRORLEVEL 230
- 27.7 Probing Commands 230
- 27.7.1 PROBE 230
- 27.7.2 SYSTEM 231
- 27.7.3 FRUVER 231
- 27.7.4 BMCVER 232
- 27.7.5 FOUND 232
- 27.8 Update Commands 233
- 27.8.1 FRUNAME 233
- 27.8.2 FRUADDRESS 234
- 27.8.3 FRUAREA 234
- 27.8.4 MULTIREC 235
- 27.8.5 FRUFIELD 236
- 27.8.6 Input of Data 240
- 27.9 Display Commands 240
- 27.9.1 DISPLAY 241
- 27.9.2 CONFIGURATION 241
- 27.9.3 Input Commands 241
- 27.9.4 MENU 241
- 27.9.5 MENUTITLE 242
- 27.9.6 MENUPROMPT 242
- 27.9.7 PROMPT 242
- 27.9.8 YES 243
- 27.9.9 NO 243
- 27.10 Command Quick Reference 243
- FRU Update Configuration File 244
- Unrecognized Sensor Types 28 253
- EventCodeNumber 254
- 28.3 SNMP Trap Raw Format 255
- 28.3.1 SNMP Trap Control 256
- 28.3.3 Configuring SEL Format 257
- Warranty Information 29 259
- 29.3 For the Americas 260
- Customer Support 30 262
- Certifications 31 263
- Agency Information 32 264
- 32.3.1 English 265
- 32.3.2 French 265
- 32.5 Japan VCCI Class A 266
- 32.6 Korean Class A 266
- 32.7 Australia, New Zealand 266
- Safety Warnings 33 267
- 33.1 Mesures de Sécurité 268
- 33.2 Sicherheitshinweise 270
- 33.3 Norme di Sicurezza 272
- 33.5 Chinese Safety Warning 276
- Example CLI Commands A 277
- Example CLI Commands 278
- Data Sheet Reference B 280
- Customer Support C 281
Manuais e produtos relacionados com não Intel MPCMM0001
não Intel 21555 Manual do Utilizador
(198 páginas)
(198 páginas)
não Intel TS13X BXTS13X Manual do Utilizador
(84 páginas)
(84 páginas)
(2 páginas)
não Intel I7 Manual do Utilizador
(1 páginas)
(1 páginas)
não Intel E8500 Manual do Utilizador
(54 páginas)
(54 páginas)
não Intel 82830M GMCH Manual do Utilizador
(53 páginas)
(53 páginas)
não Intel BXSTS200PNRW Ficha Técnica
(31 páginas)
(31 páginas)
não Intel BXSTS200P Ficha Técnica
(23 páginas)
(23 páginas)
não Intel RTS2011AC Ficha Técnica
(60 páginas)
(60 páginas)
não Intel AXXRSBBU3 Ficha Técnica
(13 páginas)
(13 páginas)
não Intel RTS2011AC Especificações
(60 páginas)
(60 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.020 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais