Intel RK80546KG0882MM Ficha Técnica

R Document Number: 254239-002 mPGA604 Socket Mechanical Design Guide March 2005

Assembled Component and Package Description R 10 mPGA604 Socket Mechanical Design Guide

R mPGA604 Socket 11 Mechanical Design Guide 3 Mechanical Requirements 3.1 Attachment A retention system needs to isolate any load in excess of 222.4

Mechanical Requirements R 12 mPGA604 Socket Mechanical Design Guide 3.5 Markings All markings required in this section must be able to withstand a t

R Mechanical Requirements mPGA604 Socket 13 Mechanical Design Guide 3.7 Socket/Package Translation During Actuation The socket shall be built so t

Mechanical Requirements R 14 mPGA604 Socket Mechanical Design Guide CFCs and HFCs shall not be used in manufacturing the socket. It is recommended t

R Mechanical Requirements mPGA604 Socket 15 Mechanical Design Guide maintain Critical Process Parameters controlling these CTFs or will provide dir

Mechanical Requirements R 16 mPGA604 Socket Mechanical Design Guide

R mPGA604 Socket 17 Mechanical Design Guide 4 Electrical Requirements Socket electrical requirements are measured from the socked-seating plane of t

Electrical Requirements R 18 mPGA604 Socket Mechanical Design Guide Table 4-2. Definitions (Sheet 2 of 2) 4 Maximum Average Contact Resistance. Ref

R Electrical Requirements mPGA604 Socket 19 Mechanical Design Guide Figure 4-3 shows the resistance test fixtures separately and superimposed. The

R 2 mPGA604 Socket Mechanical Design Guide INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL® PRODUCTS. NO LICENSE, EXPRESS OR IMP

Electrical Requirements R 20 mPGA604 Socket Mechanical Design Guide

R Electrical Requirements mPGA604 Socket 21 Mechanical Design Guide Table 4-3. Resistance Test Fixture Netlist (Sheet 1 of 2) DC Endpoints Edg

Electrical Requirements R 22 mPGA604 Socket Mechanical Design Guide Table 4-3. Resistance Test Fixture Netlist (Sheet 2 of 2) DC Endpoints Edgef

R Electrical Requirements mPGA604 Socket 23 Mechanical Design Guide 4.3 Inductance The bottom fixture for the inductance measurement is a ground pl

Electrical Requirements R 24 mPGA604 Socket Mechanical Design Guide 4.3.1 Design Procedure for Inductance Measurements The measurement equipment re

R Electrical Requirements mPGA604 Socket 25 Mechanical Design Guide 4.3.2 Correlation of Measurement and Model Data Inductance To correlate the me

Electrical Requirements R 26 mPGA604 Socket Mechanical Design Guide Table 4-4. Net list for FSETV4 Rev 1 Edge Fingers Edge Fingers +I: A61 Jumpers

R mPGA604 Socket 27 Mechanical Design Guide 5 Environmental Requirements Design, including materials, shall be consistent with the manufacture of un

Environmental Requirements R 28 mPGA604 Socket Mechanical Design Guide 5.1 Mixed Flowing Gas Test will be defined in a future revision of this docum

R mPGA604 Socket 29 Mechanical Design Guide 6 Validation Testing Requirements This section of the document outlines the tests that must be successf

R mPGA604 Socket 3 Mechanical Design Guide Contents 1 Introduction ...

Validation Testing Requirements R 30 mPGA604 Socket Mechanical Design Guide Typical examples of significant changes include, but are not limited to,

R mPGA604 Socket 31 Mechanical Design Guide 7 Safety Requirements Design, including materials, shall be consistent with the manufacture of units tha

Safety Requirements R 32 mPGA604 Socket Mechanical Design Guide

R mPGA604 Socket 33 Mechanical Design Guide 8 Documentation Requirements The socket supplier shall provide Intel with the following documentation: •

Documentation Requirements R 34 mPGA604 Socket Mechanical Design Guide

R mPGA604 Socket 35 Mechanical Design Guide 9 Mechanical Drawings These drawings refer to the mPGA604 socket. Note: Intel reserves the right to ma

Mechanical Drawings R 36 mPGA604 Socket Mechanical Design Guide Figure 9-2. mPGA604 Socket Drawing (Sheet 2 of 4)

R Mechanical Drawings mPGA604 Socket 37 Mechanical Design Guide Figure 9-3. mPGA604 Socket Drawing (Sheet 3 of 4)

Mechanical Drawings R 38 mPGA604 Socket Mechanical Design Guide Figure 9-4. mPGA604 Socket Drawing (Sheet 4 of 4)

R Mechanical Drawings mPGA604 Socket 39 Mechanical Design Guide Figure 9-5. 603-Pin Interposer Assembly Drawing (Sheet 1 of 6)

R 4 mPGA604 Socket Mechanical Design Guide 5.2 Solvent Resistance ...

Mechanical Drawings R 40 mPGA604 Socket Mechanical Design Guide Figure 9-6. 603-Pin Interposer Assembly Drawing (Sheet 2 of 6)

R Mechanical Drawings mPGA604 Socket 41 Mechanical Design Guide Figure 9-7. 603-Pin Interposer Assembly Drawing (Sheet 3 of 6)

Mechanical Drawings R 42 mPGA604 Socket Mechanical Design Guide Figure 9-8. 603-Pin Interposer Assembly Drawing OLGA Keepout (Sheet 4 of 6)

R Mechanical Drawings mPGA604 Socket 43 Mechanical Design Guide Figure 9-9. 603-Pin Interposer Assembly Drawing FCBGA2 Keepout (Sheet 5 of 6)

Mechanical Drawings R 44 mPGA604 Socket Mechanical Design Guide Figure 9-10. 603-Pin Interposer Assembly Drawing (Sheet 6 of 6) §

R Mechanical Drawings mPGA604 Socket 45 Mechanical Design Guide

R mPGA604 Socket 5 Mechanical Design Guide Revision History Revision Number Description Date 001 • Initial release of the document. October 2003

R 6 mPGA604 Socket Mechanical Design Guide Re-Validation Notice to Socket Vendors Any significant change to the socket will require submission of

R mPGA604 Socket 7 Mechanical Design Guide 1 Introduction 1.1 Objective This document defines a surface mount, Zero Insertion Force (ZIF) socket int

Introduction R 8 mPGA604 Socket Mechanical Design Guide

R mPGA604 Socket 9 Mechanical Design Guide 2 Assembled Component and Package Description The mPGA604 socket dimensions and characteristics must be